Rough-country 683X Manuel d'utilisateur télécharger pdf

JEEP JK 6” 4 DR X-SERIES SUSPENSION KIT

Thank you for choosing Rough Country for your suspension needs.

Rough Country recommends a certified technician install this system. In addition to these instructions, professional

knowledge of disassemble/reassembly procedures as well as post installation checks must be known. Attempts to install

this system without this knowledge and expertise may jeopardize the integrity and/or operating safety of the vehicle.

Please read instructions before beginning installation. Check the kit hardware against the parts list. Be sure you have all

needed parts and know where they go. Also please review tools needed list and make sure you have needed tools.

PRODUCT USE INFORMATION

As a general rule, the taller a vehicle is, the easier it will roll. Seat belts and shoulder harnesses should be worn at all

times. Avoid situations where a side rollover may occur. Generally, braking performance and capability are decreased

when larger/heavier tires and wheels are used. Take this into consideration while driving. Do not add, alter, or fabricate

any factory or after-market parts to increase vehicle height over the intended height of the Rough Country product pur-

chased. Mixing component brands is not recommended.

Rough Country makes no claims regarding lifting devices and excludes any and all implied claims. We will not be re-

sponsible for any product that is altered.

This kit features Rough Country’s adjustable joint design. Adjustable end tool is included in kit.

Assemble the joints per the separate instruction sheet Part # 92RCJ120 provided

This 6” suspension system was developed using a 37X12.50X17 tire with 4.5” to 4.75” of back spacing on aftermarket

wheels. Stock wheels can be used with this kit with up to a 35x12.5 tire, but different tire manufactures designs may re-

sult in a tire width that could result in contact with the lower control arm and/or front sway bar link in a sharp turn. Please

consult with your tire and wheel expert before purchasing. Also note that if wider tires are desired, offset wheels will be

required.

IMPORTANT NOTE : Upon completing the install of this kit the draglink must be adjusted to center the steering

wheel BEFORE the vehicle is driven. Failure to do so will cause a computer error, odd handling, and poor per-

formance.

Drive-shafts are available from Rough Country. The stock drive-shafts DO NOT have enough range of motion,

thus the shaft joints bottom out and damage will occur. The stock shafts can NOT be used and new yoke style

shafts are necessary. Additionally on 2012 Models, additional exhaust modification on the passenger side

crossover pipe will be required for adequate clearance on the front driveshaft.

If question exist we will be happy to answer any questions concerning the design, function, and correct use of our prod-

ucts by calling 1-800-222-7023.

NOTICE TO DEALER AND VEHICLE OWNER

Any vehicle equipped with any Rough Country product should have a “Warning to Driver” decal installed on the inside of

the windshield or on the vehicle’s dash. The decal should act as a constant reminder for whoever is operating the vehi-

cle of its unique handling characteristics.

INSTALLING DEALER - it is your responsibility to install the warning decal and forward these installation instructions on

to the vehicle owner for review. These instructions should be kept in the vehicle for its service

Tools Needed:

10mm Wrench 21mm Socket Jack

21mm Wrench Jack Stand Grinder

18mm Wrench 7/16” Wrench 13/32” Drill Bit

18mm Socket 9/16” Wrench Drill

19mm Wrench 9/16” Socket Pitman arm puller

19mm Deep Well Socket Reciprocating Saw

33mm Socket 13/16” Socket

7/8” Wrench

921683X00

1 2 3 4 5 6 ... 11 12

, using a 19mm deep well 8

Résumé du contenu

Page 1

JEEP JK 6” 4 DR X-SERIES SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified techni

Page 2

13. Install the supplied rear coil shim as shown in Photo 6. 14. Install the rear coil springs. Rotate the coils so that they seat properly, raise the

Page 3

23. Remove the rubber brake line from the steel line using a 12mm wrench as shown in Photo 12 and remove the brake line from the caliper using a 15mm

Page 4

POST INSTALLATION 1. Confirm that the draglink was adjusted to the center steering wheel BEFORE the vehicle is driven. Failure to do so will cause

Page 5

Kit Includes: 9248 Fr Coil Springs 9249 Rr Coil Springs 1683XBox1: 2-Fr Upper Adj Arms 2-Fr Lwr Adj Arms 1-Rr Pass Upper Arm 1-Rr Dr Uppe

Page 6

TORQUE SPECIFICATIONS Size Grade 5 Grade 8 5/16” 15 ft/lbs 20 ft/lbs 3/8” 30 ft/lbs 35 ft

Page 7

FRONT INSTALLATION INSTRUCTIONS 1. Prior to installing this kit, with the vehicle on the ground, measure the heights of your vehicle. This measu

Page 8 - , using a 19mm deep well

13. Adjust the lower control arms to a length of 22 7/8” from center of hole to center of hole and tighten the jam nut using a 1 7/8” wrench. Install

Page 9

20. Install the bushings and sleeves from 1681bag2 in the shock box into the RCX shock absorber Part # 660585. Po-sition the cup washer and stem bushi

Page 10

28. Tighten all 3/8” hardware using a 9/16” wrench. 29. This next two steps will be performed if the stock stabilizer is retained. On 07-10 Models

Page 11

37. Mark the holes to be drilled and remove the bracket from the frame. See Photo 23. 38. Drill the two holes per side using a 17/64” drill bit. See P

Page 12

REAR INSTALLATION INSTRUCTIONS 1. Chock front wheels. Jack up the rear of the vehicle and support the vehicle with jack stands, so that the rear whe