Rough-country 209 Manuel d'utilisateur télécharger pdf

Thank you for choosing Rough Country for your suspension needs. We appreciate your business!!

This kit will not fit vehicles equipped with electric steering or trucks with factory auto leveling or auto ride systems.

Important note: Please refer to the instructions on the last page for trimming the tie rods. For alignment purposes,

it will be necessary to trim/shorten the tie rod end to allow the front end alignment to be set properly.

Rough Country recommends a certified technician install this system. In addition to these instructions, professional knowl-

edge of disassemble/reassembly procedures as well as post installation checks must be known. Attempts to install this sys-

tem without this knowledge and expertise may jeopardize the integrity and/or operating safety of the vehicle.

Please read instructions before beginning installation. Check the kit hardware. Be sure you have all needed parts and know

where they go.

PRODUCT USE INFORMATION

As a general rule, the taller a vehicle is, the easier it will roll. Seat belts and shoulder harnesses should be worn at all times.

Avoid situations where a side rollover may occur. Generally, braking performance and capability are decreased when larger/

heavier tires and wheels are used. Take this into consideration while driving. Do not add, alter, or fabricate any factory or

after-market parts to increase vehicle height over the intended height of the Rough Country product purchased. Mixing com-

ponent brands is not recommended.

Rough Country makes no claims regarding lifting devices and excludes any and all implied claims. We will not be responsi-

ble for any product that is altered. We will be happy to answer any questions concerning the design, function, and correct

use of our products.

This kit is packaged as a leveling kit—raising the front 7 1/2” and the rear 6”.

Due to differences in manufacturing, dimension and inflated measurements, tire and wheel combinations should be test fit

prior to installation. For this application we recommend a 18” or larger wheel not to exceed 9” in width. When using a 18”

wheel backspacing should be maximum of 5.5” and a minimum 5.0” . With a 20” or larger wheel backspacing should be a

maximum of 6.0” and a min of 5.5”. Additionally a quality tire of radial design is recommended, not exceeding 35” tall and

12.5” wide. Please note that use of a 35” x 12.5” tire may require modification to the front valance.

Optional kicker Bars Part #1262 are available for this kit. Please contact you local Rough Country Dealer for infor-

mation.

NOTICE TO DEALER AND VEHICLE OWNER

Any vehicle equipped with any Rough Country product should have a “Warning to Driver” decal installed on the inside of the

windshield or on the vehicle’s dash. The decal should act as a constant reminder for whoever is operating the vehicle of its

unique handling characteristics.

INSTALLING DEALER - it is your responsibility to install the

warning decal and forward these installation instructions on to

the vehicle owner for review. These instructions should be kept

in the vehicle for its service life.

We hope installing your Rough Country lift kit is a positive

experience. Please note that variations in construction and

assembly in the vehicle manufacturing process will virtually

ensure that some parts may seem difficult to install. Addi-

tionally, the current trend in manufacturing of vehicles re-

sults in a frame that is highly flexible and may shift slightly

on disassembly prior to installation. The use of pry bars and

tapered punches for alignment is considered normal and

usually does not indicate a faulty product. However, if you

are uncertain about some aspect of the installation process,

please feel free to call our tech support department at 800-

222-7023. We do not recommend that you modify the Rough

Country parts in any way as this will void any warranty ex-

pressed or implied.

92120900

07-UP AVALANCHE 7.5” KIT

1 2 3 4 5 6 ... 13 14

Résumé du contenu

Page 1 - 07-UP AVALANCHE 7.5” KIT

Thank you for choosing Rough Country for your suspension needs. We appreciate your business!! This kit will not fit vehicles equipped with electric s

Page 2

54. Install the supplied brake line relocation bracket on the upper control arm mount with the stock hardware. Slightly pull down on the brake line a

Page 3

REAR INSTALLATION INSTRUCTIONS 1. Chock the front wheels and jack up the rear of the vehicle. Support the vehicle with jack stands. 2. Remove the

Page 4

11. Install the new coil springs in the stock location. Reinstall the lower control arms on the axle with the stock hardware and tighten using a 21mm

Page 5

18. Remove the brake line from the brake line bracket using a 1/2” wrench. See Photo 13. 19. Install the new brake line bracket as shown in the stoc

Page 6 - Electrical Plug

Thank you for choosing Rough Country for all of your suspension needs. TEMPLATE FOR SWAY BAR RELOCATION Cut out template and position template on l

Page 7

1264Box1 Front Cross Member Rear Cross Member 1264Box3 Driver Knuckle Pass Knuckle 1209Box1 Front Strut Spacers Driver Diff Bracket Pa

Page 8

DIAGRAM SHOWN WITH OPTIONAL KICKER BARS PART #1262 INSTALLED CAD DRAWING SHOWING KIT COMPONENTS AND INSTALLED LOCATIONS Torque Specs: Size Gr

Page 9

FRONT INSTALLATION 1. Park the vehicle on a level surface and chock the rear wheels. 2. Jack up the front of the vehicle. Place jack stands under t

Page 10

10. Remove the sway bar & end links from the lower control arm as shown in Photo 7 using a 15mm wrench. 11. Remove the sway bar from the frame

Page 11

Photo 16 Cut here Photo 18 17. Make an alignment mark to show relationship between driveshaft and differential input flange. Using a 11mm wrench, re

Page 12

25. Install the front cross member as shown in Photo 19 with the supplied 5/8” x 4 1/2” bolts, nuts /washers. Do not tighten at this time. 26. On th

Page 13

35. Reinstall the lower control arms in the cross member brackets with the factory hardware. Do not tighten at this time. 36. Install the supplied 3

Page 14

45. Trim tie rod ends as per instructions on last page and install on the knuckle. Tighten using a 21mm wrench. 46. Install the sway bar drop brack

Commentaires sur ces manuels

Pas de commentaire

Rough-country 209 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Rough-country 209. Rough Country 209 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Rough-country 209